AD260 |
RFQ for AD260 Required Field |
 |
| Technical/Catalog Information | AD260AND-0 |
| Vendor | Analog Devices Inc |
| Category | Isolators |
| Number of Channels | 5 |
| Package / Case | 22-DIP (Staggered Leads) |
| Propagation Delay | 15ns |
| Data Rate | - |
| Configuration | 3/2 |
| Output Type | Logic |
| Isolation Rating | 3.5kVrms |
| Packaging | Tube |
| Voltage - Supply | 4.5 V ~ 5.5 V |
| Operating Temperature | -25°C ~ 85°C |
| RoHS Status | RoHS Non-Compliant |
| Other Names | AD260AND 0 AD260AND0 |
| Product | Manufacturers | Pack | D/C |
| AD260 | - | - | 2000+ |
The AD260 is designed using Analog Devices new IsoLogic circuit architecture to isolate five digital control signals to/ from a microcontroller and its related field I/O components. Six models allow all I/O combinations from five input lines to five output lines, including combinations in between. Every AD260 effectively replaces up to five opto-isolators while also providing the 1.5 W transformer for a 3.5 kV isolated dc-dc power supply circuit.
Each line of the AD260 has a bandwidth of 20 MHz (min) with a propagation delay of only 14 ns, which allows for extremely fast data transmission. Output waveform symmetry is maintained to within ±1 ns of the input so the AD260 can be used to accurately isolate time-based PWM signals.
All field or system output pins of the AD260 can be set to a high resistance three-state level by use of the two enable pins. A field output three-stated offers a convenient method of presetting logic levels at power-up by use of pull-up/down resistors. System side outputs being three-stated allows for easy multiplexing of multiple AD260s.
Typical Application |
Features |
| ·PLC/DCS Analog Input and Output Cards·Communications Bus Isolation·General Data Acquisition Applications·IGBT Motor Drive Controls·High Speed Digital I/O Ports | `IsoLogic™ Circuit Architecture`Isolation Test Voltage: To 3.5 kV rms`Five Isolated Logic Lines: Available in Six I/O Configurations`Logic Signal Bandwidth: 20 MHz (Min), 40 mbps (NRZ)`Isolated Power Transformer: 37 V p-p, 1.5 W Max`CMV Transient Immunity: 10 kV/ms Min`Waveform Edge Transmission Symmetry: 61 ns`Field and System Output Enable/Three-State Functions`Performance Rated Over 258C to +858C`UL1950, IEC950, EN60950 Certification, Pending |
| Parameter | Conditions | Min Typ Max | Units |
| Supply Voltage (+5 V dcSYS & FLD) DC Input Voltage (VIN MAX) DC Output Voltage (VOUT MAX) Clamp Diode Input Current (IIK) Clamp Diode Output Current (IOK) Output DC Current, per Pin (IOUT) DC Current, VCC or GND (ICC or IGND) Storage Temperature (TSTG) Lead Temperature (Soldering, 10 sec) Electrostatic Protection (VESD) |
Referred to +5 V dcSYS & FLD and 5 V RTNSYS & FLD Respectively Referred to +5 V RTNSYS & FLD and 5 V dcSYS & FLD Respectively For VI < 0.5 V or VI > 5 V RTNSYS & FLD +0.5 V For VO < 0.5 V or VO > 5 V RTNSYS & FLD +0.5 V Per MIL-STD-883, Method 3015 |
0.5 +6.0 0.5 +0.5 0.5 +0.5 25 +25 25 +25 25 +25 50 +50 40 +85 +300 4.5 5 |
V |
